TTM-HS2V SERIES
TTM-HSTS LIQUID SILICONE SERIES
TTM-HS2V ROTARY INSERT MOLDING MACHINE
TTM-HSTS ROTARY INSERT LIQUID SILICONE MACHINE
| Featuring: | Standard Features: | |
Vertical Injection |
|
25 ton equivalent hydraulic clamp |
12, 6, or 4 station rotary table, 25" diameter x 5/8" thick. |
|
Automatic Knock-out with adjustable height |
30mm screw for 2oz injection or22mm screw for 1 oz injection |
|
PID auto tune dual display temperature controllers |
Standard mold base 4" X 4 1/2" |
|
D2 Screw bright-hardened |
Non-Standard mold base 5" X 6" |
|
Bimetallic nickel-cobalt lined barrel |
Special size maximum 6" X 7" for the 25" diameter table. |
|
Tree-piece titanium nitride check valve |
|
|
|
Solid state microprocessor with 100 function timers |
|
|
|
Fahrenheit / Centigrade temperature controller readout |
|
|
|
Molded parts counter |
|
|
|
Security access code |
|
|
|
Cycle countdown LED display |
|
|
|
Automatic/single cycle molding selection |
|
|
|
Spring less shut off nozzle |
|
|
|
9.5 GPM variable displacement compensated pump |
|
|
|
Cord tray for parts handling |
|
|
|
Open mold detection |
|
|
|
90 degree oscillating table feature / shuttle |
|
|
|
10 micron spin-off oil filter |
|
|
|
Cold start-up screw protection |
|
|
|
Transparent hopper and cover with quick removal |
|
|
|
Oil level sight gage with temperature display |
|
|
|
Barrel temperature watchdog alert |
|
|
|
Oil reservoir heat exchanger |
| STANDARD SPECIFICATIONS | 22MM SCREW | 30 MM SCREW |
Maximum Shot Size ( PS ) |
1 OZ. |
2 OZ. |
Screw Diameter ( inches ) |
.860" |
1.174" |
L/D Ration ( length to diameter ) |
20:1 |
16:1 |
Injection Stroke ( inches ) |
4.0 |
4.0 |
Screw Speed |
275 RPM max |
275 RPM max |
Screw Recovery Rate ( in./sec. ) |
.50 |
.50 |
Screw Recovery Rate ( oz./sec. ) |
.125 |
.250 |
Plasticizing Capacity ( lbs./hr ) |
22 lbs |
45 lbs. |
Barrel Heaters ( watts ) |
2,800 |
2,800 |
Molding Clamping Force |
12 Ton* / 25 equivalent |
12 Ton* / 25 equivalent |
Ejector Stroke |
1.5" max |
1.5" max |
Hydraulic Reservoir Capacity |
33 gallons |
33 gallons |
Pump Output |
9.5 GPM |
9.5 GPM |
Normal High Pressure |
1,825 PSI |
1,800 PSI |
Normal Low Pressure |
700 PSI |
700 PSI |
Maximum Operating Pressure |
2,500 PSI |
2,500 PSI |
Minimum Operating Pressure, with low pressure molding kit |
100 PSI |
100 PSI |
Power Requirements |
208-240 volts3 phase 40 amps |
208-240 volts3 phase 40 amps |
Motor |
7.5 HP @ 1.750RPM 208240/480 Volt60 HZ 3 Phase |
7.5 HP @ 1.750RPM208240/480 Volt60 HZ 3 Phase |
Overall Dimensions ( inches ) |
67"W x 82"L x 93.5"W |
67"W x 82"L x 93.5"W |
Shipping Weight, Without Oil |
2,500 lbs. |
2,500 lbs |
MODEL TTM-HS2 ROTARY TABLE INSERT MOLDING MACHINE
DESCRIPTION
MODEL TTM-HS2 VERTICAL INSERT MOLDING MACHINE INCLUDING:
22MM/1-OZ OR 3OMM/2-OZ RECIPROCATING SCREW INJECTION,
4, 6 or 12 STATION, 25" DIAMETER 5/8" STAINLESS STEEL ROTARY TABLE,
25 TON EQUIVALENT HYDRO MECHANICAL CLAMP,
THREE ZONE BARREL HEATING WITH 5 HEATER BANDS,
MICROPROCESSOR-BASED CONTROLS,
AUTOMATIC KNOCK-OUT,HEAT EXCHANGER FOR OIL COOLING
OPTIONAL:
MOLD OPENER RAMP, SPRUE TRIMMER, ROTARY WATER MANIFOLD,
VARIABLE PROGRAMMABLE SHOT SIZE CONTROLLER, AIR LOGIC- BASIC
PROVISION,
LOW PRESSURE MOLDING KIT, 33" STAINLESS STEEL ROTARY TABLE,
STAINLESS HOPPER WITH MANUAL SHUTOFF, AIR HEAT EXCHANGER
FOR OIL COOLING.
Terms: 1/2 with order - Balance on delivery F.O.B. BICKNELL IN.
Shipment: 10 weeks after receipt of purchase order and initial payment.
*All shipping and handling charges are to be paid for by the customer*
Remarks: TABLE TURNS 180 DEGREES IN 3.4 SECONDS. 4-station table,
It takes 1.66 seconds index time per station.
California Customers: A California Sales Tax of 7.5% shall be the customer’ responsibility.